• 0113 345 5170
  • info@alpol.co.uk
  • 178 Easterley Road, Leeds, West Yorkshire ,LS8 3AD

RENDER COLOURING TOOL

MATERIALS CALCULATOR

0113 3455170

£108.00 Cart
£108.00 Cart

AT 320 White mineral dashed plaster 1.5 mm

Category
For decorative thin-coat internal and external plaster coating (e.g. for ALPOL EKO PLUS STANDARD, ALPOL EKO PLUS PREMIUM and ALPOL TERMO BIS EPS board – based thermal insulation systems or ALPOL EKO PLUS WM and ALPOL TERMO STROP mineral wool – based thermal insulation systems). The plaster coating can be painted with ALPOL AF 640, AF 660, AF 680, AF 685 façade paints or ALPOL AI 785 colourant. For hand application or by means of mechanical spraying.

£21.00

Substrate type
Reinforced layer with mesh, embedded in adhesive ALPOL AK 527, AK 531, AK 532, AK 533 or AK 534, primed mineral wool in ALPOL TERMO STROP systemand cement and cement-lime plasters, seasoned concrete surfaces, gypsum plasters and gypsum boards.

Substrate preparation
The substrate should be dry, clean, stable, sound (reinforcing layer at least 3 days after embedding mesh in adhesive, plaster – 28 days after application, seasoned concrete). Remove brittle, loose and peeling material with poor adhesion, patch damages with ALPOL AZ 130 quick-setting mortar or ALPOL AZ 135 levelling mortar. Strengthen loose substrates with ALPOL AG 700 deep-penetrating primer. To reduce substrate absorption, if necessary, use primer for absorbing substrates ALPOL AG 704. At least 24 hours before plaster application, treat the substrate with ALPOL AG 701 primer. Pre-primed mineral wool does not require additional treatment.

Instructions for use
Mix the entire contents of the bag mechanically or manually with specified amount of clean and cold water, to bring the mixture to homogeneous and required consistency. After 5 minutes, stir the prepared mix again. Spread the plaster with a steel float, and level it accordingly. Use a plastic float to make a textured finish. In case of mechanical spraying increase amount of batched water accordingly and adjust plaster consistency depending on spraying unit type. The plaster should be sprayed with a uniform jet perpendicularly to the surface from a distance at least of 30 cm. Use the plaster within 1 hour from mixing with water. If the mix thickens in that period of time, stir it thoroughly again without adding water. Adding too much water will prolong setting time and impair all product characteristics including adhesion and strength. Do not use dirty or rusty tools or containers. Plaster may be painted when set, after a minimum of 3–7 days since application (depending on the type of paint and weather conditions).

Tools
Mixer or low-speed electric drill, basket mixer, stainless steel float and trowel, plastic float, scaled container for dosing water, container for plaster.

Working conditions
Work in ambient temperatures between +5°C and +25°C. Do not add any other agents than batched water. Protect fresh plaster coat from excessive drying, moisture and direct sunlight. Using scaffolding guards is recommended.

Storage
Store in original, unopened packages in dry place – shelf life 12 months from production date. Protect from moisture during transport and storage.

Notes
The specifications and instructions for use are given for the temperature of (20±2)°C and relative air humidity of (65±5)%. The workability may alter in different conditions. Irritating to eyes and respiratory system. Appropriate eye, respiratory system and skin protection measures should be used. Becomes alkaline after mixing with water. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Keep away from children. Use water to remove fresh dirt or ALPOL AI 770 cleaner to remove hardened dirt. The manufacturer accepts no responsibility for damage caused by unskilful or inappropriate use of the product.

General recommendations
Work according to building practice, observing health & safety standards and regulations as well as the instructions referring to ALPOL EKO PLUS STANDARD, ALPOL EKO PLUS PREMIUM and ALPOL TERMO STROP thermal insulation systems, as well as the Building Research Institute (ITB) instructions.

Specifications
Composition: blend of white cement, lime, white quartz sand, mineral admixtures and additives
Bulk density approx. 1.5 kg/dm3
Appropriate amount of water between 4.5 and 5.5 litres per 25 kg of dry mix
Setting time approx. 24 hours
Final Set approx. 3 days
Consistency as per slump cone test approx. 9 cm
Workability within 1 hour from mixing with water
Granulation 1,5 mm
Yield approx. 16 dm³ from 25 kg
Coverage approx. 2 kg/m²

Description

For decorative thin-coat internal and external plaster coating (e.g. for ALPOL EKO PLUS STANDARD, ALPOL EKO PLUS PREMIUM and ALPOL TERMO BIS EPS board – based thermal insulation systems or ALPOL EKO PLUS WM and ALPOL TERMO STROP mineral wool – based thermal insulation systems). The plaster coating can be painted with ALPOL AF 640, AF 660, AF 680, AF 685 façade paints or ALPOL AI 785 colourant. For hand application or by means of mechanical spraying.

Additional information

Weight 25 kg

Related products

Call our Dedicated Support team on 0113 345 5170

Alpol Proffesional Building Materials is a nationwide distributor that specialises in the selling and distribution of Rendering , plastering and building materials. High quality with great results, 100% 5 star reviews. Bringing suppliers and manufacturers together as a community, with advice and support.

Navigation

Useful Links

Contact