• 0113 345 5170
  • Info@alpol.co.uk
  • 178 Easterley Road, Leeds, West Yorkshire ,LS8 3AD

RENDER COLOURING TOOL

MATERIALS CALCULATOR

0113 3455170

AM 800 White polymer finish coat ALPOL Putz S

Categories ,

For applying a thin-layer smooth finish on plasters, gypsum boards, paint coatings and concrete substrates. For patching slightly chipped areas and irregularities on plaster and concrete surfaces. Also suitable for pointing gypsum board joints using reinforcing tape. Suitable for use on walls and ceilings inside the buildings, in rooms unexposed to moisture. For hand or machine application. Especially recommended for application with the use of hydrodynamic units.

 

Package
Single: 20 kg bag

£21.00

Instructions for use
Stir the bag contents manually or mechanically with specified amount of clean and cold water to bring the mixture to homogenous and required consistency. Allow 5 minutes and stir the entire mix again. Spread the finish coat with a stainless steel float to form a layer between 1 and 2 mm thick, until smooth and regular finish is achieved. Apply the second coat after the first one has set. After the second coat has dried out, grind all irregularities with sand paper or a grinding mesh. Unused product can be used later, if stored in a tightly closed container.

Substrate type
Gypsum, cement, cement-lime and lime plasters, gypsum boards, dispersion and oil paint coats as well as concrete substrates.

Substrate preparation
Substrate should be seasoned, clean, dry, stable and sound. Remove remains of paint and other contamination. Significantly chipped areas should be patched with ALPOL AZ 130 quick setting mortar or ALPOL AZ 135 levelling mortar. Treat the loose surface with ALPOL AG 700 or ALPOL AG 704 deep penetrating primer to reduce substrate absorption, if necessary. Patch small cracks and scratches with a thin coat of the product. Bubbles in concrete substrate and very coarse plaster surfaces should be filled thoroughly.

Tools
Low-speed electric mixer, basket mixer, finish coat application unit, stainless steel floats, putty knive, trowel, hand sander with mesh or sandpaper.

Working conditions
Work in ambient and substrate temperatures between +5Ā°C and +25Ā°C. Low temperature and high air humidity prolong drying time of the finish coat. Do not allow the fresh finish coat to moisten or dry excessively. Attention must be paid to ensure good room ventilation.

Storage
Store in original, unopened packages in dry place ā€“ shelf life 12 months from production date. Protect from moisture during transport and storage.

Notes
The specifications and instructions for use are given for the temperature of (23Ā±2)Ā°C and relative air humidity of (50Ā±5)%. The technical properties and characteristics may alter in different conditions. Irritating to eyes and respiratory system. Appropriate eye, respiratory system and skin protection measures should be used. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Keep away from children. Use water to remove fresh dirt or ALPOL AI 770 cleaner to remove hardened dirt. The manufacturer accepts no responsibility for damage caused by unskilful or inappropriate use of the product.

General recommendations
Work according to building practice, observing health & safety standards and regulations.

Specifications
Composition: blend of white gypsum fillers, admixtures and additives
Bulk density approx. 1.0 kg/dmĀ³
Appropriate amount of water approx. 8 dmĀ³/20 kg
approx. 1.6 dmĀ³/4 kg
approx. 0.4 dmĀ³/kg
One coat drying time:
ā€“ on non-primed surface
ā€“ on primed surface		 approx. 6 h
approx. 12 h
Crack strength no cracks within 50 mm from the thin end of a wedge
Bending strength (destroying load) ā‰„ 200 N
Adhesion to gypsum plasterboard ā‰„ 0.25 N/mmĀ² or board damage
Granulation:
– residual on sieve 0.315 mm
– residual on sieve 0.2 mm		 0% of the compound
ā‰¤ 1% of the compound
Fire resistance class A2-s1, d0
Yield approx. 19 dmĀ³ out of 20 kg
approx. 3.5 dmĀ³ out of 4 kg
approx. 0.95 dmĀ³ out of 1 kg
Coverage approx. 1.1 kg/mĀ²/mm

Description

For applying a thin-layer smooth finish on plasters, gypsum boards, paint coatings and concrete substrates. For patching slightly chipped areas and irregularities on plaster and concrete surfaces. Also suitable for pointing gypsum board joints using reinforcing tape. Suitable for use on walls and ceilings inside the buildings, in rooms unexposed to moisture. For hand or machine application. Especially recommended for application with the use of hydrodynamic units.

 

Package
Single: 20 kg bag

Related products

Call our Dedicated Support team on 0113 345 5170

Alpol Proffesional Building Materials is a nationwide distributor that specialises in the selling and distribution of Rendering , plastering and building materials. High quality with great results, 100% 5 star reviews. Bringing suppliers and manufacturers together as a community, with advice and support.

Navigation

Useful Links

Contact

Alpol West Midland
+44 1384 671711

Leeds
+01133455170

Alpol West Midland
Ā  +44 1384 671711

Leeds
Ā  +01133455170

Please enable JavaScript in your browser to complete this form.